View 27L512-20_993708.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? operating current: 10ma@ 3.6v, 5mhz ? standby current: 10ua ? package type: - 28 pin plastic dip - 32 pin plcc - 28 pin 8 x 13.4 mm tsop(i) 1 pin configurations pdip general description the mx27l512 is a 3v only, 512k-bit, one-time programmable read only memory. it is organized as 64k words by 8 bits per word, operates from a single +3volt supply, has a static standby mode, and features fast single address location programming. all program- ming signals are ttl levels, requiring a single pulse. for programming outside from the system, existing eprom programmers may be used. the mx27l512 supports intelligent fast programming algorithm which can result in programming time of less than fifteen seconds. this eprom is packaged in industry standard 28 pin dual-in-line packages , 32 lead plcc, and 28 lead tsop(i) packages. features ? 64k x 8 organization ? wide voltage range, 2.7v to 3.6v ? +12.5v programming voltage ? fast access time: 120/150/200/250ns ? totally static operation ? completely ttl compatible p/n: pm0256 rev. 2.6, aug. 26, 2003 block diagram pin description plcc 8 x 13.4mm 28tsop(i) symbol pin name a0~a15 address input q0~q7 data input/output ce chip enable input oe/vpp output enable input/program supply voltage nc no internal connection vcc power supply pin gnd ground pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 a15 a12 a7 a6 a5 a4 a3 a2 a1 a0 q0 q1 q2 gnd 28 27 26 25 24 23 22 21 20 19 18 17 16 15 vcc a14 a13 a8 a9 a11 oe/vpp a10 ce q7 q6 q5 q4 q3 mx27l512 1 4 5 9 13 14 17 20 21 25 29 32 30 a8 a9 a11 nc oe/vpp a10 ce q7 q6 a6 a5 a4 a3 a2 a1 a0 nc q0 q1 q2 gnd nc q3 q4 q5 a7 a12 a15 nc vcc a14 a13 mx27l512 oe/vpp a11 a9 a8 a13 a14 vcc a15 a12 a7 a6 a5 a4 a3 22 23 24 25 26 27 28 1 2 3 4 5 6 7 a10 ce q7 q6 q5 q4 q3 gnd q2 q1 q0 a0 a1 a2 21 20 19 18 17 16 15 14 13 12 11 10 9 8 mx27l512 mx27l512 512k-bit [64k x 8] cmos eprom control logic output buffers q0~q7 ce oe/vpp a0~a15 address inputs y-decoder x-decoder y-select 512k bit cell maxtrix vcc gnd . . . . . . . . . . . . . . . .
2 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 auto identify mode the auto identify mode allows the reading out of a binary code from an eprom that will identify its manufacturer and device type. this mode is intended for use by programming equipment for the purpose of automatically matching the device to be programmed with its corresponding programming algorithm. this mode is functional in the 25 c 5 c ambient temperature range that is required when programming the mx27l512. to activate this mode, the programming equipment must force 12.0 0.5(vh) on address line a9 of the device. two identifier bytes may then be sequenced from the device outputs by toggling address line a0 from vil to vih. all other address lines must be held at vil during auto identify mode. byte 0 ( a0 = vil) represents the manufacturer code, and byte 1 (a0 = vih), the device identifier code. for the mx27l512, these two identifier bytes are given in the mode select table. all identifiers for manufacturer and device codes will possess odd parity, with the msb (q7) defined as the parity bit. read mode the mx27l512 has two control functions, both of which must be logically satisfied in order to obtain data at the outputs. chip enable (ce) is the power control and should be used for device selection. output enable (oe) is the output control and should be used to gate data to the output pins, independent of device selection. assuming that addresses are stable, address access time (tacc) is equal to the delay from ce to output (tce). data is available at the outputs toe after the falling edge of oe, assuming that ce has been low and addresses have been stable for at least tacc - toe. standby mode the mx27l512 has a cmos standby mode which reduces the maximum vcc current to 10 ua. it is placed in cmos standby when ce is at vcc 0.3 v. the mx27l512 also has a ttl-standby mode which reduces the maximum vcc current to 0.25 ma. it is placed in ttl-standby when ce is at vih. when in standby mode, the outputs are in a high-impedance state, independent of the oe input. functional description the programming of the mx27l512 when the mx27l512 is delivered, or it is erased, the chip has all 512k bits in the "one", or high state. "zeros" are loaded into the mx27l512 through the procedure of programming. for programming, the data to be programmed is applied with 8 bits in parallel to the data pins. vcc must be applied simultaneously or before vpp, and removed simultaneously or after vpp. when programming an mxic eprom, a 0.1uf capacitor is required across vpp and ground to suppress spurious voltage transients which may damage the device. fast programming the device is set up in the fast programming mode when the programming voltage oe/vpp = 12.75v is applied, with vcc = 6.25 v, (algorithm is shown in figure 1). the programming is achieved by applying a single ttl low level 100us pulse to the ce input after addresses and data line are stable. if the data is not verified, an additional pulse is applied for a maximum of 25 pulses. this process is repeated while sequencing through each address of the device. when the programming mode is completed, the data in all address is verified at vcc = 5v 10%. program inhibit mode programming of multiple mx27l512s in parallel with different data is also easily accomplished by using the program inhibit mode. except for ce and oe, all like inputs of the parallel mx27l512 may be common. a ttl low-level program pulse applied to an mx27l512 ce input with oe/vpp = 12.5 0.5v will program that mx27l512. a high-level ce input inhibits the other mx27l512s from being programmed. program verify mode verification should be performed on the programmed bits to determine that they were correctly programmed. the verification should be performed with oe/vpp and ce, at vil. data should be verified tdv after the falling edge of ce.
3 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 notes: 1. vh = 12.0 v 0.5 v 2. x = either vih or vil 3. a1 - a8 = a10 - a15 = vil(for auto select) 4. see dc programming characteristics for vpp voltage during programming. two-line output control function to accommodate multiple memory connections, a two- line control function is provided to allow for: 1. low memory power dissipation, 2. assurance that output bus contention will not occur. it is recommended that ce be decoded and used as the primary device-selecting function, while oe be made a common connection to all devices in the array and connected to the read line from the system control bus. this assures that all deselected memory devices are in their low-power standby mode and that the output pins are only active when data is desired from a particular memory device. system considerations during the switch between active and standby conditions, transient current peaks are produced on the rising and falling edges of chip enable. the magnitude of these transient current peaks is dependent on the output capacitance loading of the device. at a minimum, a 0.1 uf ceramic capacitor (high frequency, low inherent inductance) should be used on each device between vcc and gnd to minimize transient effects. in addition, to overcome the voltage drop caused by the inductive effects of the printed circuit board traces on eprom arrays, a 4.7 uf bulk electrolytic capacitor should be used between vcc and gnd for each eight devices. the location of the capacitor should be close to where the power supply is connected to the array. mode select table pins mode ce oe/vpp a0 a9 outputs read vil vil x x dout output disable vil vih x x high z standby (ttl) vih x x x high z standby (cmos) vcc 0.3v x x x high z program vil vpp x x din program verify vil vil x x dout program inhibit vih vpp x x high z manufacturer code(3) vil vil vil vh c2h device code(3) vil vil vih vh 91h
4 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 figure1. fast programming flow chart start address = first location vcc = 6.25v oe/vpp = 12.75v program one 100us pulse x = 0 last address ? verify byte vcc = 5.25v device passed compare all bytes to original data device failed increment address fail pass no no yes yes address = first location last address ? increment address fail pass increment x x = 25 ? no oe/vpp = vil yes program one 100us pulse
5 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 switching test circuits switching test waveforms device under test diodes = in3064 or equivalent cl = 100 pf including jig capacitance 6.2k ohm 1.8k ohm +5v cl 2.0v 0.8v test points input 2.0v 0.8v output ac testing: ac driving levels are 2.4v/0.4v for both commercial grade and industrial grade. input pulse rise and fall times are < 10ns. ac driving levels
6 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 notice: stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. exposure to absolute maximum rating conditions for extended period may affect reliability. notice: specifications contained within the following tables are subject to change. dc characteristics absolute maximum ratings rating value ambient operating temperature -40 o c to 85 o c storage temperature -65 o c to 125 o c applied input voltage -0.5v to 7.0v applied output voltage -0.5v to vcc + 0.5v vcc to ground potential -0.5v to 7.0v a9 & vpp -0.5v to 13.5v dc/ac operating conditions for read operation mx27l512 -12 -15 -20 -25 operating commercial 0 c to 70 c0 c to 70 c0 c to 70 c0 c to 70 c temperature industrial -40 c to 85 c -40 c to 85 c -40 c to 85 c -40 c to 85 c vcc power supply 2.7v to 3.6v 2.7v to 3.6v 2.7v to 3.6v 2.7v to 3.6v symbol parameter min. max. unit conditions voh output high voltage vcc-0.3 v ioh = -100ua, vcc = 3.0v vol output low voltage 0.3 v iol = 2.1ma, vcc = 3.0v vih input high voltage 2.0 vcc + 0.5 v vil input low voltage -0.3 0.6 v ili input leakage current -10 10 ua vin = 0 to 3.6v ilo output leakage current -10 10 ua vout = 0 to 3.6v icc3 vcc power-down current 10 ua ce = vcc 0.3v icc2 vcc standby current 0.25 ma ce = vih icc1 vcc active current 10 ma ce = vil, f=5mhz, iout = 0ma, vcc=3.6v ipp vpp supply current read 10 ua ce = vil, vpp = vcc capacitance ta = 25 o c, f = 1.0 mhz (sampled only) symbol parameter min. max. unit conditions cin input capacitance 8 12 pf vin = 0v cout output capacitance 8 12 pf vout = 0v vpp vpp capacitance 18 25 pf vpp = 0v
7 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 ac programming characteristics ta = 25 o c 5 c symbol parameter min. max. unit conditions tas address setup time 2 us tds data setup time 2 us tah address hold time 0 us tdh data hold time 2 us tdfp chip enable to output float delay 0 130 ns tvps vpp setup time 2 us tpw ce program pulse width 95 105 us tvcs vcc setup time 2 us tdv data valid from ce 150 ns toeh oe/vpp hold time 2 ns tvr oe/vpp recovery time 2 ns 27l512-12 27l512-15 27L512-20 27l512-25 symbol parameter min. max. min. max. min. max. min. max. unit conditions tacc address to output delay 120 150 200 250 ns ce = oe = vil tce chip enable to output delay 120 150 200 250 ns oe = vil toe output enable to output 60 65 100 120 ns ce = vil delay tdf oe high to output float, 0 40 0 50 0 60 0 70 ns or ce high to output float toh output hold from address, 0 0 0 0 ns ce or oe which ever occurred first ac characteristics dc programming characteristics ta = 25 o c 5 o c symbol parameter min. max. unit conditions voh output high voltage 2.4 v ioh = -0.40ma vol output low voltage 0.4 v iol = 2.1ma vih input high voltage 2.0 vcc + 0.5 v vil input low voltage -0.2 0.8 v ili input leakage current -10 10 ua vin = 0 to 5.5v vh a9 auto select voltage 11.5 12.5 v icc3 vcc supply current(program & verify) 40 ma ipp2 vpp supply current(program) 30 ma ce = vil vcc1 fast programming supply voltage 6.00 6.50 v vpp1 fast programming voltage 12.5 13.0 v
8 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 waveforms read cycle fast programming algorithm waveform address inputs data out oe ce data address valid data tdf tacc tce toe toh addresses ce oe/vpp data vcc vih vil vpp1 vil vcc1 vcc vih vil data out valid hi-z tas tvps tvcs tdv tpw tds tdh tvr tvps tah tdfp program verify program
9 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 plastic package part no. access time(ns) operating standby operating package current max.(ma) current max.(ua) temperature mx27l512pc-12 120 10 10 0 c to 70 c 28 pin dip mx27l512qc-12 120 10 10 0 c to 70 c 32 pin plcc mx27l512tc-12 120 10 10 0 c to 70 c 28 pin tsop(i) mx27l512pc-15 150 10 10 0 c to 70 c 28 pin dip mx27l512qc-15 150 10 10 0 c to 70 c 32 pin plcc mx27l512tc-15 150 10 10 0 c to 70 c 28 pin tsop(i) mx27l512pc-20 200 10 10 0 c to 70 c 28 pin dip mx27l512qc-20 200 10 10 0 c to 70 c 32 pin plcc mx27l512tc-20 200 10 10 0 c to 70 c 28 pin tsop(i) mx27l512pc-25 250 10 10 0 c to 70 c 28 pin dip mx27l512qc-25 250 10 10 0 c to 70 c 32 pin plcc mx27l512tc-25 250 10 10 0 c to 70 c 28 pin tsop(i) mx27l512pi-12 120 10 10 -40 c to 85 c 28 pin dip mx27l512qi-12 120 10 10 -40 c to 85 c 32 pin plcc mx27l512ti-12 120 10 10 -40 c to 85 c 28 pin tsop(i) mx27l512pi-15 150 10 10 -40 c to 85 c 28 pin dip mx27l512qi-15 150 10 10 -40 c to 85 c 32 pin plcc mx27l512ti-15 150 10 10 -40 c to 85 c 28 pin tsop(i) mx27l512pi-20 200 10 10 -40 c to 85 c 28 pin dip mx27l512qi-20 200 10 10 -40 c to 85 c 32 pin plcc mx27l512ti-20 200 10 10 -40 c to 85 c 28 pin tsop(i) mx27l512pi-25 250 10 10 -40 c to 85 c 28 pin dip mx27l512qi-25 250 10 10 -40 c to 85 c 32 pin plcc mx27l512ti-25 250 10 10 -40 c to 85 c 28 pin tsop(i) ordering information
10 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 package information
11 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512
12 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512
13 p/n:pm0256 rev. 2.6, aug. 26, 2003 mx27l512 revision history revision no. description page date 2.0 1)programming flow chart corrected, programming verify after 6/05/1997 whole array programmed with 1 pulse. 2) eliminate interactive programming mode. 3) add 28-tsop(i) and 28-sop packages offering. 4) ac driving levels are changed from 2.4v/0.3v to 2.4v/0.4v. 2.1 general description, ".... is a 5v only..." ==> "....is a 3v only...." 9/25/1998 2.2 cancel ceramic dip package type p1,2,9,11 mar/02/2000 2.3 remove 28-pin sop package p1,9 sep/19/2001 package information format changed p10~12 2.4 remove "ultraviolet erasable" wording p1 apr/24/2002 2.5 to modify package information p10~12 nov/19/2002 2.6 to modify 32-plcc package information p11 aug/26/2003 a1: from 0.50mm(0.020 inch)/nom. to 0.58mm(0.023 inch)/nom. from 0.66mm(0.026 inch)/nom. to 0.81mm(0.032 inch)/nom.
mx27l512 m acronix i nternational c o., l td. headquarters: tel:+886-3-578-6688 fax:+886-3-563-2888 europe office: tel:+32-2-456-8020 fax:+32-2-456-8021 japan office: tel:+81-44-246-9100 fax:+81-44-246-9105 singapore office: tel:+65-348-8385 fax:+65-348-8096 taipei office: tel:+886-2-2509-3300 fax:+886-2-2509-2200 m acronix a merica, i nc. tel:+1-408-453-8088 fax:+1-408-453-8488 chicago office: tel:+1-847-963-1900 fax:+1-847-963-1909 http : //www.macronix.com macronix international co., ltd. reserves the right to change product and specifications without notice.

▲Up To Search▲

Price & Availability of 27L512-20

	To Download 27L512-20 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .